Can Engineered Hardwood Be Refinished?

I'm Cristobal, and I refinish hardwood floors around Atlanta every week. One of the questions I hear most from homeowners in newer townhomes in Vinings, Smyrna and East Cobb is simple: "My floors are engineered. Can you still sand them?" The honest answer is: usually yes, but it depends on one thing, the thickness of the top layer of real wood.

What engineered hardwood is

Engineered hardwood is a plank made of layers. The bottom is plywood or a high-density core, and the top is a slice of real oak, hickory, maple or walnut. That top slice is called the wear layer. Solid hardwood is real wood all the way through, so it can be sanded many times. With engineered wood, everything depends on how much real wood sits on top of the core.

A lot of builders in metro Atlanta switched to engineered floors in the 2000s and 2010s because it handles our humidity better than solid wood and can go over concrete slabs. So if your home was built in the last 20 years, there is a good chance you have it.

How I check if your floor can be sanded

Before I promise anything, I look at the wear layer. The easiest place is a floor vent: I lift the register and look at the edge of a board, where you can see the layers. I also check a threshold or the edge at the top of the stairs.

If the floor was already sanded once by someone else, I check that too. I'd rather tell you no than ruin a floor that only needed a fresh coat.

Screen and recoat: the other option

When sanding isn't safe, or the floor only has light wear, I do a screen and recoat. I buff the existing finish with a fine screen so the new coat can bond, clean everything, and put on one or two fresh coats of polyurethane. It doesn't remove deep scratches or change the color, but it brings back the shine, protects the wood, and is done in about a day. For engineered floors in busy kitchens and hallways, I often recommend doing this every few years so you never need a full sanding.

What Georgia humidity does to engineered floors

Engineered hardwood moves less than solid wood, which is why builders like it here. But our wet summers still matter. I see edges that have lifted near dishwashers and refrigerators, and gaps that open in winter when the heat runs. Before I refinish, I check moisture levels. If boards are swollen or delaminating, sanding won't fix that, and I'll tell you which boards should be replaced first. Keeping your home between about 35 and 55 percent humidity all year helps the floor and the new finish last.

Stain on engineered floors

If the wear layer is thick enough to sand, you can change the color, just like with solid wood. Many engineered floors in Atlanta are white oak or hickory. White oak takes natural, light browns and grays nicely. Hickory has strong grain and color changes, so I always put samples down on your actual floor first so you see the real result in your own light.

When I recommend replacing instead

Sometimes refinishing isn't the right call: the wear layer is worn through, there is water damage across a large area, or boards are peeling apart. In that case, I'll tell you straight and show you what I see. I also do installations, so I can talk you through options without pushing a job you don't need.

Frequently asked questions

How many times can engineered hardwood be refinished? It depends on the wear layer. Thick wear layers (around 4 to 6 mm) can be sanded two or three times. Thin ones can't be sanded at all and should only get a screen and recoat.

How do I know if my floor is engineered or solid? Look at the edge of a board at a floor vent or stair nose. If you see layers of plywood under the top wood, it's engineered. Send me a photo and I'll tell you.

Does refinishing engineered hardwood cost less than replacing it? In most cases refinishing or a screen and recoat costs much less than new floors. The exact price depends on square footage, repairs and stairs, so text me photos and I'll give you an exact price.

How long does it take? A screen and recoat is usually one day. A full sand and refinish on an average Atlanta home takes three to four days, plus drying time before furniture goes back.

Related pages

Not sure what you have? Call or text Cristobal at 404-796-7650. Send a photo of a board edge at a floor vent and a few pictures of the room, and I'll tell you if your engineered floor can be sanded and give you an exact price.

More: Hardwood floor refinishing · All service areas

Text me your project

Fill this in and it opens a text to Cristobal with your details. Photos of the floor help me give you a price faster.

On a computer? Just call or text 404-796-7650.

Call 404-796-7650Text